2011/10/16

[bb]nfsブートできた!が・・・

nfsvers=3を指定することで、BeagleBoardからnfsブートすることができた。
よかったよかった。

Linux version 2.6.32 (xxx@kurokiri) (gcc version 4.4.3 (GCC) ) #21 Sat Oct 15 14:07:24 JST 2011CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 Beagle Board
Memory policy: ECC disabled, Data cache writeback
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp 720m )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 25146
Kernel command line: mem=99M console=ttyS2,115200n8 noinitrd ip=192.168.0.22::192.168.0.1:255.255.255.0 root=/dev/nfs nfsroot=192.168.0.2:/home/xxx/Qt/nfs,nfsvers=3,nolock,rsize=1024,wsize=1024 rootfstype=nfs mpurate=600 omapfb.rotate=1 omapfb.vrfb=y vram=10M omapfb.vram=0:10M omapdss.def_disp=dvi omapfb.mode=dvi:720x480MR-16@60Booting kernel: `0:10M' invalid for parameter `omapfb.vram'
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 99MB = 99MB total
Memory: 94904KB available (4312K code, 811K data, 168K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
Reprogramming SDRC clock to 332000000 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER12 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 514.67 BogoMIPS (lpj=2011136)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
Registering NAND on CS0
Unable to get DVI reset GPIO
Target VDD1 OPP = 5, VDD2 OPP = 3
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VPLL2: 1800 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV normal standby
regulator: VAUX3: 1800 mV normal standby
regulator: VAUX4: 1800 mV normal standby
i2c_omap i2c_omap.2: bus 2 rev3.12 at 100 kHz
i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 185
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for cp210x
usbcore: registered new interface driver cp210x
cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
android init
android_probe pdata: c048f2dc
android_bind
android_usb gadget: android_usb ready
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
f_adb init
android_register_function adb
adb_bind_config
f_mass_storage init
android_register_function usb_mass_storage
f_accessory init
android_register_function accessory
mice: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0
using rtc device, twl_rtc, for alarms
twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
twl_rtc twl_rtc: Power up reset detected.
twl_rtc twl_rtc: Enabling TWL-RTC.
i2c /dev entries driver
Linux video capture interface: v2.00
sn9c102: V4L2 driver for SN9C1xx PC Camera Controllers v1:1.47pre49
usbcore: registered new interface driver sn9c102
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
logger: created 64K log 'log_system'
Advanced Linux Sound Architecture Driver Version 1.0.21.
usb 1-2: new high speed USB device using ehci-omap and address 2
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
OMAP3 Beagle SoC init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
  #0: omap3beagle (twl4030)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Power Management for TI OMAP3.
Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
IVA2 clocking rate: 430 MHz
SmartReflex driver initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
regulator_init_complete: incomplete constraints, leaving VAUX3 on
regulator_init_complete: incomplete constraints, leaving VDVI on
regulator_init_complete: incomplete constraints, leaving VDAC on
twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
usb 1-2.2: new full speed USB device using ehci-omap and address 3
pegasus 1-2.2:1.0: setup Pegasus II specific registers
IP-Config: No network devices available.
fail ic_open_devs()
pegasus 1-2.2:1.0: eth0, MELCO/BUFFALO LUA2-TX, 00:40:26:c0:bf:af
mmc0: new high speed SD card at address b368
mmcblk0: mmc0:b368 SDC   1.85 GiB
 mmcblk0: p1
pegasus 1-2.2:1.0: update_eth_regs_async, status -22
IP-Config: Complete:
     device=eth0, addr=192.168.0.22, mask=255.255.255.0, gw=192.168.0.1,
     host=192.168.0.22, domain=, nis-domain=(none),
     bootserver=255.255.255.255, rootserver=192.168.0.2, rootpath=
Looking up port of RPC 100003/3 on 192.168.0.2
Looking up port of RPC 100005/3 on 192.168.0.2
NFS: sending MNT request for server:/home/xxx/Qt/nfs
NFS: MNT request succeeded
VFS: Mounted root (nfs filesystem) on device 0:12.
Freeing init memory: 168K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
modprobe: FATAL: Could not load /lib/modules/2.6.32/modules.dep: No such file or directory
modprobe: FATAL: Could not load /lib/modules/2.6.32/modules.dep: No such file or directory
modprobe: FATAL: Could not load /lib/modules/2.6.32/modules.dep: No such file or directory
modprobe: FATAL: Could not load /lib/modules/2.6.32/modules.dep: No such file or directory
Populating dev cache
Remounting root file system...
WARNING: Couldn't open directory /lib/modules/2.6.32: No such file or directory
FATAL: Could not open /lib/modules/2.6.32/modules.dep.temp for writing: No such file or directorymodprobe: FATAL: Could not load /lib/modules/2.6.32/modules.dep: No such file or directory
modprobe: FATAL: Could not load /lib/modules/2.6.32/modules.dep: No such file or directory
root: mount: mounting rootfs on / failed: No such file or directory
root: mount: mounting usbfs on /proc/bus/usb failed: No such file or directory
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... done.
Wed Dec  2 19:18:00 UTC 2009
Configuring update-modules
WARNING: Couldn't open directory /lib/modules/2.6.32: No such file or directory
FATAL: Could not open /lib/modules/2.6.32/modules.dep.temp for writing: No such file or directoryINIT: Entering runlevel: 5
Starting telnet daemon.
modprobe: FATAL: Could not load /lib/modules/2.6.32/modules.dep: No such file or directory
Starting syslogd/klogd: done
Starting thttpd.

あれ、止まってる・・・。

/lib/modules/2.6.32がない、というのが大きいようだ。
この環境は、元はといえばTI提供のもので、kernelは2.6.29-rc3-omap1だったのだ。
しかし、あまりにも動かなかったので、Androidで使っていた2.6.32を使っている。
その差が現れたか・・・。
対策は2つしかなく、
  • kernelを2.6.29-rc3-omap1にする
  • 環境を2.6.32にする

のどっちかだ。
あまり考えず、TIのAndroid kernelでmake modulesさせてみよう。
make modules_install・・・だけだと/lib以下にコピーされるので、INSTALL_MOD_PATHを指定してから実行。

INIT: version 2.86 booting
Please wait: booting...
Starting udev
udev: starting version 141
udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

udevd[541]: inotify_add_watch(3, (null), 10) failed: Bad address

Remounting root file system...
root: mount: mounting rootfs on / failed: No such file or directory
root: mount: mounting usbfs on /proc/bus/usb failed: No such file or directory
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... done.
Wed Dec  2 19:18:00 UTC 2009
INIT: Entering runlevel: 5
Starting telnet daemon.
Starting syslogd/klogd: done
Starting thttpd.

やっぱり、無理矢理はだめなんかね・・・。

0 件のコメント:

コメントを投稿

コメントありがとうございます。
スパムかもしれない、と私が思ったら、
申し訳ないですが勝手に削除することもあります。

注: コメントを投稿できるのは、このブログのメンバーだけです。